Sonel

About Sonel

Sonel was established in June 1994. The company's founders were electrical engineers - people with a good knowledge of the market needs for specialized test equipment. In 1998 company's name and its legal status had changed and as a result SONEL S.A. was established. The company debuted on the Warsaw Stock Exchange in June 2008.

Featured Products
Products
Photovoltaic Meters

PVM-1020 KIT

  • It can be used for category 1 measurements according to IEC 62446-1.
  • AUTO mode for performing a sequence of measurements after one press of the START button.
  • It converts measured parameters into STC conditions according to IEC 60891.

PVM-1020

  • It can be used for category 1 measurements according to IEC 62446-1.
  • AUTO mode for performing a sequence of measurements after one press of the START button.
  • It converts measured parameters into STC conditions according to IEC 60891.

IRM-1

  • Measurement of solar radiation and temperature.
  • The LoRa interface for communication with the PVM-1020 meter – offers a larger range than the Bluetooth technology!
  • Automatic data synchronization with the PVM-1020 meter.
Insulation Resistance Meters

MIC-2511

  • Leakage current measurement during R ISO measurement
  • Capacitance measurement during R ISO measurement
  • Low-voltage measurement of circuit continuity and resistance
  • Temperature measurement (ST-1 temperature probe)
  • Measurement of DC and AC

MIC-15K1

  • Partial discharge indicator PDI.
  • Diagnostics of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD.
  • It allows testing the electrical durability of the tested object - breakdown voltage indication.
  • High resistance

MIC-5001

  • Measurement voltage selected within the range of 50…500V with steps of 50V
  • Continuous reading of measured insulation resistance or leakage current
  • Automatic discharge of the measured object’s capacitance upon completion of insulation resistance measurement

MIC-2501

  • Measurement voltage within the range of 100…2500 V, selected in steps of 100 V
  • Continuous reading of measured insulation resistance or leakage current
  • Automatic discharge of the measured object’s capacitance upon completion of insulation resistance measurement,

MIC-10K1

  • Insulation resistance measurement up to 40 TΩ
  • Measurement voltage - any in the range of 50…10000 V, 50…1000 V with steps of 10 V, 1…10 kV with steps of 25
  • Continuous indication of measured insulation resistance or leakage current

MIC-5050

  • Insulation resistance measurement up to 20 TΩ
  • Measurement voltage - any in the range of 50…5000 V, 50…1000 V with steps of 10 V, 1…10 kV with steps of 25 V
  • Continuous indication of measured insulation resistance or leakage current

MIC-5010

  • Measuring voltage in the range of 50…5000 V, 50…1000 V in steps of 10 V, 1…5 kV in steps of 25 V
  • Continuous indication of measured insulation resistance and leakage current
  • Automatic discharge of measured object capacitance voltage

MIC-5005

  • Measuring voltage in the range of 50…5000 V, 50…1000 V in steps of 10 V, 1…5 kV in steps of 25 V
  • Continuous indication of measured insulation resistance and leakage current
  • Automatic discharge of measured object capacitance voltage

MIC-30

  • Measurement of insulation resistance up to 100 GΩ thanks to max 1000 V measurement voltage
  • Designed for harsh environmental conditions conditions – IP67 ingress protection

MIC-10

  • Measurement of insulation resistance up to 10 GΩ thanks to max 1000 V measurement voltage
  • Designed for harsh environmental conditions - IP67 ingress protection
  • Testing electrical continuity

MIC-5

  • Measuring voltage: 250 V or 500 V,
  • Low-voltage resistance measurement in the range of 0…1999 Ω
  • Measurement of direct and alternating voltages in the range of 0…600 V
Earth Resistance Meters

MRU-120HD

  • 3-pole and 4-wire method – measurement of earthing systems using auxiliary probes
  • 3-pole method with clamp – measurement of earthing systems with multiple earth electrodes
  • Two-clamp method – measurement of earthing system when the auxiliary probes cannot be used

MRU-11

  • 3-pole and 4-wire method – measurement of earthing systems using auxiliary probes
  • 2-pole method
  • Earth resistivity – Wenner method
  • Resistance of auxiliary electrodes RH and RS
  • Measurement of interference voltage to 100

MRU-10

  • 3-pole method-measurement of earthing systems using auxiliary probes
  • 2-pole method
  • Resistance of auxiliary electrodes RH and RS
  • Measurement of interference voltage to 100 V
  • Indication of battery state

MRU-200-GPS

  • 3-pole and 4-wire method – measurement of earthing systems using auxiliary probes
  • 3-pole method with clamp – measurement of earthing systems with multiple earth electrodes
  • Two-clamp method – measurement of earthing system when the auxiliary probes cannot be used

MRU-200

  • 3-pole and 4-wire method – measurement of earthing systems using auxiliary probes
  • 3-pole method with clamp – measurement of earthing systems with multiple earth electrodes
  • Two-clamp method – measurement of earthing system when the auxiliary probes cannot be used

MRU-120

  • 3-pole and 4-wire method – measurement of earthing systems using auxiliary probes
  • 3-pole method with clamp – measurement of earthing systems with multiple earth electrodes
  • Two-clamp method – measurement of earthing system when the auxiliary probes cannot be used

MRU-30

  • 3-pole and 4-wire method – measurement of earthing systems using auxiliary probes
  • 3-pole method with clamp – measurement of earthing systems with multiple earth electrodes
  • Two-clamp method – measurement of earthing system when the auxiliary probes cannot be used

MRU-21

  • 3-wire method – measurement of earthing systems using auxiliary probes
  • 2-wire method – simplified measurement of resistance-to-earth
  • Resistance of earth & compensatory conductors measured using current ≥200 mA with auto-zero function
Thermal Imaging Camera

KT-800M

  • 400 x 300 px infrared uncooled Vox detector
  • Automatic focus on a person's face
  • Warning sound alarm when a person with fever is detected

KT-128

  • The Sonel KT-128 thermal imaging camera is a special camera..
  • Cost-effective, practical and handy, it is a powerful tool for everyday work. The camera is used for basic.

DIT-120

  • Sonel DIT-120 is the pyrometer for professionals.
  • Durable housing, ergonomic grip, buttons accessible with one finger - all this contributes to the comfort of the user.

DIT-200

  • Sonel DIT-200 is the pyrometer for professionals.
  • Durable housing, ergonomic grip, buttons accessible with one finger - all this contributes to the comfort of the user.

KT-670.1

  • Image files saved in JPG format (complete image data).
  • Recording of IR videos (on SD memory card or computer hard disk).
  • Built-in reports module.

KT-650.1

  • Image files saved in JPG format (complete image data).
  • Recording of IR videos (on SD memory card or computer hard disk).
  • Built-in reports module.

KT-560.1

  • Image files saved in JPG format (complete image data).
  • Recording of IR videos (on SD memory card or computer hard disk).
  • Built-in reports module.

KT-256

  • Measuring range -20°C...550°C (-20°F... 1022°F)
  • Quick start
  • Fast temperature measurement
  • Automatic signalling

KT-560M

  • Measuring range 20°C…60°C, accuracy ≤ ±0.4°C
  • 5 Mpix visual camera
  • Imaging Modes: IR, visual, PIP, MIF

KT-120M

  • Measuring range 20°C…50°C
  • Accuracy up to ±0.5°C
  • Automatic signalling of fever detection

DIT-10MED

  • Measurement of body temperature, surface, food and liquids.
  • Possibility to set temperature limit alarm.

KT-400

  • High sensitivity of detectors and a wide temperature range
  • Photos in increased resolution

DIT-130

  • Precise non-contact temperature measurement
  • Type K temperature measurement
  • Ergonomic gun-type housing

DIT-500

  • Precise non-contact temperature measurement
  • Type K temperature measurement
  • Ergonomic gun-type housing

KT-165

  • Solid and portable tool,
  • Intuitive user interface
  • 1-hand operation,
  • High-capacity, replaceable Li-Ion battery

KT-200

  • high sensitivity of detectors and a wide temperature range
  • comprehensive image analysis tools
  • intuitive user interface

KT-650

  • Troubleshooting electrical installations, wiring, panels, motors, breakers, transformers, switchgear and electrical.
  • Monitoring the thermal performance of industrial manufacturing processes.
  • Inspecting buildings for insulation leaks

KT-250

  • Solid and portable tool,
  • Intuitive user interface
  • 1-hand operation,
  • High-capacity, replaceable Li-Ion battery
  • Different imaging modes: IR, visual, PIP, MIF
  • Built-in visual camera: 5 MPix

KT-320

  • Solid and portable tool,
  • Intuitive user interface
  • 1-hand operation,
  • High-capacity, replaceable Li-Ion battery
  • Different imaging modes: IR, visual, PIP, MIF
  • Built-in visual camera: 5 MPix
Power Quality Analysis

PQM-707

  • 7” touchscreen - ergonomic and intuitive graphical user interface.
  • Over 10 years of recording.
  • CAT IV 600 V measurement category - high safety.

PQM-711

  • Remote control and data transfer through a built-in GSM modem.
  • Anti-theft feature – SMS notification in the event of position change (built-in GPS receiver).

PQM-710

  • Remote control and data transfer through a built-in GSM modem.
  • Anti-theft feature – SMS notification in the event of position change (built-in GPS receiver).

PQM-700

  • 4 current inputs, physical measurement of current in the neutral conductor.
  • Registration of up to 1100 parameters, including average, maximum, minimum .
Low Resistance Meters

MMR-6700

  • Measurements of resistive objects with current up to 200 A
  • Measurements of induction objects up to 10 A
  • Measurement with one- or both-way current flow

MMR-6500

  • Measurements of resistive objects with current up to 100 A
  • Measurements of induction objects up to 10 A
  • Measurement with one- or both-way current flow

MMR-650

  • Measurement of winding resistance (inductive objects including amorphous core)
  • Measurement of very low resistance
  • Transformer core demagnetization function

MMR-640

  • Measurement of very low resistance
  • High immunity to disturbances
  • Easy operation
  • Automatic measurement mode

MMR-630

  • Measurements of objects resistive in nature:
    • Welded and soldered connections, equipotential bondings, earthing conductors,
    • contacts, welds of rails, conductors and cables,
    • measurement according to the four-lead method.

MMR-620

  • Measurements of objects resistive in nature:
    • Welded and soldered connections, equipotential bondings, earthing conductors,
    • contacts, welds of rails, conductors and cables,
    • measurement according to the four-lead method.
Multifunction Electrical Installations Meter

MPI-540-PV Solar

  • Includes MPI-540-PV Solar multi-function meter, IRM-1 solar radiation and temperature meter, PVM-1 PV adapter, C-PV clamp, test leads and other accessories
  • MPI-540-PV multifunctional meter of electrical and installation parameters created for measuring parameters of photovoltaic installations

MPI 540-PV

  • The largest touch screen on the market (7”) – remarkable ergonomics and ease of use
  • Removable microSD memory card – easy increase of memory capacity
  • Li-Ion battery – longer operation of the meter
  • Cooperation with solar radiation and temperature meter

MPI-540 + EVSE-01

  • Testing home and industrial electrical installations
  • Measurements of electric vehicle charging stations – quickly and in accordance with applicable regulations
  • To facilitate diagnostics, one of the Sonel EVSE-01 sockets is provided with pulse width modulation signal (PWM).

MPI-536

  • Measurement of insulation resistance using test voltage of 2.5 kV
  • Visualization of RISO in the form of a graph
  • The largest touch screen on the market (7”) – remarkable ergonomics and ease of use
  • Removable microSD memory card – easy increase of memory

MPI-540

  • The largest touch screen on the market (7”) – remarkable ergonomics and ease of use
  • Removable microSD memory card – easy increase of memory capacity
  • Li-Ion battery – longer operation of the meter

MPI-535

  • The largest touch screen on the market (7”) – remarkable ergonomics and ease of use
  • Removable microSD memory card – easy increase of memory capacity
  • Li-Ion battery – longer operation of the meter

MPI-530

  • Impedance measurement with resolution 0,001 Ω and 23 A current – short-circuit resistor RZW=10 Ω,
  • Measurement range: 95…440 V, frequency 45…65 Hz,
  • Short circuit loop impedance with resolution 0,01 Ω

MPI-530-IT

  • Measurement of short circuit loop impedance ZL-PE, ZL-N, ZL-L
  • Test current: 23/40 A; measuring range acc. to IEC 61557: 0,13…1999,9 Ω
  • Measurement of short circuit loop impedance ZL-PE in RCD mode

MPI-525

  • Short-circuit loop measurement: impedance measurement with 23 A current (44 A phase-to-phase) – short-circuit resistor R=10,
  • Short-circuit loop measurement: measurement range: 95…440 V, frequency 45…65 Hz,
  • Testing of general and selective RCD with the rated differential current of 10,30,100,300,500 and 1000 mA.

MPI-520

  • Short-circuit loop measurement: impedance measurement with 23 A current (44 A phase-to-phase) – short-circuit resistor R=10 Ω,
  • Short-circuit loop measurement: measurement range: 95…440 V, frequency 45…65 Hz,
  • Short-circuit loop measurement with resolution 0,01 Ω, in distribution network without tiggering RCD (IΔn≥30 mA)

MPI-520S

  • Short-circuit loop measurement: impedance measurement with 23 A current (44 A phase-to-phase) – short-circuit resistor R=10 Ω,
  • Short-circuit loop measurement: measurement range: 95…440 V, frequency 45…65 Hz,
  • Short-circuit loop measurement with resolution 0,01 Ω, in distribution network without tiggering RCD (IΔn≥30 mA)

MPI-507

  • Measurement of short circuit loop impedance in networks with rated voltage: 220/380 V, 230 V/400 V, 240/415 V and frequency 45…65 Hz, operating voltage range: 180…460 V
  • Insulation resistance measurement: Test voltage 100 V, 250 V, 500 V
  • Earth resistance measurement: 3-pole method​​​​​​​

MPI-506

  • Measurement of short circuit loop impedance in networks with rated voltage: 220/380 V, 230 V/400 V, 240/415 V and frequency 45…65 Hz, operating voltage range: 180…460 V
  • Testing of prompt, short-delay and selective RCDs with rated current values 10, 15, 30, 100, 300, 500 mA
  • Insulation resistance measurement: Test voltage 100 V, 250 V, 500 V

MPI-502

  • Measurements of short circuit loop impedance in networks with rated voltage: 220/380 V, 230 V/400 V, 240/415 V and frequency 45…65 Hz,
  • Testing of prompt, short-delay (general) and selective RCDs for the rated current values 10, 30, 100, 300, 500 mA,
  • Detection of the replacement L and N in the socket and automatic conversion in the meter.
Short Circuit Loop Measurements

MZC-330S

  • Measurements in installations with rated voltages between 110/190V, 115/200V, 127/220V, 220/380V, 230/400V, 240/415V, 290/500V & 400/690V & frequencies 45…65 Hz,
  • Ability to perform measurements in short circuit system: phase-phase, phase-protective, phase-neutral,
  • Differentiation between the phase voltage and the inter-phase voltage while calculating the short circuit current,

MZC-320S

  • Measurements in installations with rated voltages between: 110/190 V, 115/200 V, 127/220 V, 220/380 V, 230/400 V, 240/415 V i 290/500 V and frequencies 45…65 Hz,
  • Ability to perform measurements in short circuit system: phase-phase, phase-protective, phase-neutral,
  • Differentiation between the phase voltage and the inter-phase voltage while calculating the short circuit current,

MZC-306

  • Measurements possible in installations 110/190 V, 115/200 V, 127/220 V, 220/380 V, 230/400 V, 240/415 V, 290/500 V and 400/690 V (range 100…750 V)
  • Loop impedance measurement with resolution 0,01 Ω
  • Loop impedance measurement without tripping the circuit breaker > 30 mA with resolution 0,01 Ω (100…440 V)
  • Short circuit current indication
  • USB connection with PC

MZC-304

  • Measurements of impedance in a short circuit loop - L-PE circuit, L-N, L-L circuit, L-PE(RCD) circuit – without tripping the circuit breaker ≥ 30 mA.
  • Low voltage resistance measurement - continuity measurement – DC current +200 mA with wire resistivity reset
  • The measurements are posible in instalations 220/380 V, 230/400 V, 240/415 V with frequeency range 45…65 Hz.
  • Memory of 10 banks of 99 cells.

MZC-20E

  • Measurements of impedance in a short-circuit loop Z within the range S of 0.24…200 Ω
  • Short-circuit current IK: 1,15 – 958,3 A (Un =230 V)
  • AC voltage measurement: 0 – 440 V
  • Electrical safety: type of insulation double, according to EN 61010-1 and IEC 61557

MZC-310S

  • Measurement of very low short circuit loop impedances (with resolution 0,1 mΩ) with a current of 150 A at 230 V; maximum 280 A at 440 V or measurement with a current of 23 A at 230 V; maximum 42 A at 440 V.
  • Touch voltage and touch shock voltage measurement (with resistor 1 kΩ).
RCD Meters

MRP-201

  • AC voltage and frequency measurement.
  • PE lead connection check using a touch electrode.
  • Bulit-in memory for up to 990 cels of measurement results.
  • Wireless radio communication
Corona Camera

UV-260

  • High sensitivity to UV signals
  • Precise location of corona emitting sources
  • Auto focus of UV and visible channels
  • Back ground noise reduction
  • Built-in GPS
Illuminance Measurement

LXP-10A

  • Measurement resolution: 0.001 lx (0.001 fc).
  • High accuracy and fast response.
  • Data-hold function for holding measuring values.
  • Automatic zeroing.

LXP-10B

  • Measurement resolution: 0.01 lx (0.001 fc).
  • High accuracy and fast response.
  • Data-hold function for holding measuring values.
  • Automatic zeroing.

LXP-2

  • Measurement resolution 0.1 lx (0.01 fc).
  • High accuracy and fast response.
  • Data-hold function for holding measuring values.
  • Relative reading.
Underground Cable Locator

LKN-710P

  • The 710P transmitter - is used as a LKZ-710 type locator or as a transmitter for the P-3 type indicator.
  • It is made of the highest quality, carefully selected material, resistant to scratches and abrasion.

LKZ-1000

  • Four adjustable output levels with maximum output level of 1 W
  • Choice of 3 tracing signals, 8 kHz or 33 kHz, or at 8 kHz and 33 kHz together
  • Locates cables up to 3 m, 10 ft deep

LKZ-720

  • Detection of wires and cables (live or not).
  • Tracing underground cables.
  • Tracing conductive water and heating pipelines.
  • Flow and accurate locating the object.
  • Phase detection mode.

TDR-420

  • Fault location in power and telecommunication cables
  • Two independent cursors to indicate two fault locations and the distance between them
  • Fault location in coaxial cables

LKO-720

  • Receiver operation with max. 4 transmitters at the same time to locate interruptions or distinguish wires.
  • Receiving status information from the LKN-720 transmitter.

LKN-720

  • 4 codes of the transmitted signal.
  • Transmission of information about the transmitter settings and battery charge level.
  • Measurement of voltage at the object to 500 V RMS.
  • Three levels of amplification.

TDR-410

  • Fault location in power and telecommunication cables
  • Fault location in coaxial cables
  • Fault location in infrastructure cables
  • Graphic presentation of cable faults with an indication of the distance to the fault on the display

LKZ-1500

  • The LKZ-1500 locator set, consisting of a transmitter and receiver, allows for location, identification and tracking of the route of objects buried in the earth, i.e., power cords and cables, control cables, telecommunications cables,

LKZ-2000

  • Designed to easily trace power cables over long and short distances with pinpoint accuracy
  • Highly durable, weatherproof Sonel LKZ system has a flexible operating system
  • Locating and tracing pipes can support the mapping and surveying.

LKZ-700

  • Signaling of transmitter and receiver opeartion by LED and sound,
  • Operation in wide range of rated voltage, up to 500 V RMS,
  • Three modes of transmitter amplification,
  • Automatic or manual selection of transmitter operation modes,

MX32

  • Comprehensive fault locating in underground LV/MV/HV cable networks;
  • Covering full cycle from trouble shooting to isolating and precise fault pinpointing;
  • Central control unit with menu guided operation following the working algorithm of cable fault locating;

INTERFLEX 140

  • Isolating & pre-locating faults in various metallic cable networks;
  • Multiphase (3-phase) comparison and difference modes for faster fault evaluation and isolation;
  • Display of up to 7 curves;
  • Straightforward user friendly software menu with rotary encoder operation;

Kamphone N

  • Precise pinpointing of cable faults within underground networks in combination with suitable surge generator;
  • Simple line tracing with magnetic channel;
  • Interference suppression

P12i

  • Comprehensive fault locating in underground cable networks;
  • Optimal for 6 to 12kV cable systems;
  • Covering full cycle from trouble-shooting to isolating and precise fault pinpointing;

P16i

  • Comprehensive fault locating in underground cable networks;
  • Optimal for 6 to 15kV cable systems;
  • Covering full cycle from trouble-shooting to isolating and precise fault pinpointing;

P24i

  • Comprehensive fault locating in underground cable networks;
  • Optimal solution for LV; 10 to 11kV and 20 to 22kV cable systems;
  • Covering full cycle from trouble-shooting to isolating;

P32X

  • Comprehensive fault locating in underground LV, MV and HV cable networks;
  • Covering full cycle from trouble shooting to isolating and precise fault pinpointing;
  • Central control unit with menu guided operation following the working algorithm of cable fault locating;

INTERSELECT NLT

  • Precise identification of cables, feeders and other conductors with highly unique encoded ID sequence;
  • Cable identification in non-live IT, LV or MV power cables;
  • Cable identification in live LV cables up to 400V;

InterSheath XS

  • Testing cables in power, lighting, control and communication networks;
  • Testing electric heating cable systems;
  • Constant voltage and constant current supply;
  • Handy and simple to operate test combination;
  • Adjustable current;

InterSheath CS

  • Testing & fault locating of cables in power, lighting, control and communication networks;
  • Testing electric heating cable systems;
  • Effective pre-location & isolation of sheath faults to decrease overall required test duration;
PAT Testers

PAT-10

  • Led test results indication
  • Quick access to the measurement procedures,
  • Measurement of protective conductor resistance with the currents: 200 mA, 10 A ,

PAT-2E

  • Led test results indication
  • Quick access to the measurement procedures,
  • Measurement of protective conductor resistance with the currents: 200 mA,

PAT-2

  • Led test results indication
  • Quick access to the measurement procedures,
  • Measurement of protective conductor resistance with the currents: 200 mA,

PAT-86

  • Intuitive user interface.
  • Cooperation with a label printer and QR code scanner.
  • Operation time at rechargeable battery power supply: upto 1 hr.

PAT-85

  • Intuitive user interface.
  • Cooperation with a label printer and QR code scanner.
  • Robust, compact housing.
  • Operation time at rechargeable battery power supply: up to 1 hour.

PAT-820

  • Measurement of protective conductor resistance with the currents: 200 mA, 10 A , 25 A ( protection class I),
  • Measurement of insulation resistance – three measurement voltages: 100 V, 250 V and 500 V,
Voltage Testers

P-4

  • Automatic voltage test up to 1000 V AC/DC
  • Optical indication by a LED bar
  • Sound indication when dangerous voltage levels of 50 V AC and 120 V DC are exceeded

P-5

  • Automatic voltage test up to 1000 V AC/DC
  • Optical indication by a LED bar and additional LCD display
  • Sound indication when dangerous voltage levels of 50 V AC and 120 V DC

P-6

  • Phase identification - unique feature in voltage indicators worldwide
  • Automatic voltage test up to 1000 V AC/DC
  • Optical indication by a LED bar and additional LCD display

VT-3

  • Two AC voltage detection ranges: 12 V / 100 ... 1000 V
  • Durable, two-composite housing
  • Waterproof with IP67 protection
  • Built-in LED flashlight

VT-2

  • Non-contact detection of AC voltage from 90 V AC to 1000 V AC
  • Rugged, double molded case
  • Suitable for outlets or against wire insulation testing
Clamp Meters

CMP-400

  • Non-contact neon lamp
  • Safe, insulated measurement clamp
  • Reinforced, impact resistant enclosure

CMP-401

  • Non-contact neon lamp
  • Safe, insulated measurement clamp
  • Reinforced, impact resistant enclosure

CMP-200

  • White backlighting of display
  • Interior clamp diameter 30 mm
  • MAX function, freezing of maximum values

CMP-1006

  • Large and easy to read LCD
  • Auto range with manual selection mode
  • MAX and MIN results hold function

CMP-2000

  • INRUSH function for measuring current drawn by an electrical device when first turned on
  • True RMS AC voltage and current measurement for accurate and reliable readings of non-sinusoidal

CMP-3000

  • Counting: 50.000 digits
  • HOLD
  • Automatic range selection
  • Inrush current
  • Non-contact voltage detector
  • MIN / MAX

CMP-200F

  • Counting: 6.000 digits
  • HOLD
  • Automatic range choice zakresu
  • Open clamp meters
  • Contactless voltage gauge
  • MIN / MAX

CMP-3kR

  • Counting: 3.000 digits
  • HOLD
  • Automatic range selection
  • Inrush current
  • TRMS measurement
  • Bluetooth communication
  • Empty battery indication
Multimeters

CMM-60

  • Counting: 50.000 digits
  • The HOLD function
  • Manual / automatic range selection
  • Relative measurement

CMM-30

  • Counting: 60.000 digits
  • HOLD
  • Manual / automatic range selection
  • Relative measurement REL

CMM-11

  • Counting: 4.000 digits
  • HOLD
  • Manual / automatic range selection
  • MIN / MAX

CMM-40

  • MAX and MIN function for saving extreme values
  • AC+DC function for reading the sum of an alternating and direct component

CMM-10

  • Display: readout 5000 with function indicators
  • HOLD
  • Manual / automatic range selection
Leakage Current Alarm

MPU-1

  • Constant controlling of current flowing on earthing,
  • Measurement with the use of single clamp or two clamps simultaneously. In case of using two clamps, current value is summed up, which allows for checking twin pylons (rotational), with independent clamp for each component pylon,
  • Work mode LED indicator,
Laboratory Equipment

DB-THERMO

  • Training in thermal imaging and non-contact temperature measurements
  • Indispensable device during any training on contactless temperature measurements and thermal imaging with the use of thermographic cameras.
  • Emissivity of different materials and the influence of surface type on temperature measurement.

SRP-10G0-10T0

  • Supply voltage: 100…240 V AC (50/60 Hz)
  • Maximum power consumption: 75 VА
  • Operating temperature range: 10...30°C | 50...86°F
  • Maximum current in measuring circuit: 3 mА
  • Maximum operating voltage: 10 000 V DC

DB-1

  • Fault loop impedance for assessment of the automatic power cutoff condition,
  • RCD Parameters,
  • Earthing Resistance,
  • Soil Resistivity,
  • Continuity test of equipotential bonding,
  • Insulation Resistance,
  • Power Network Voltage.
High Voltage Equipment

S-25 DC

  • Easy Operation
  • Robust Construction, low Weight
  • Integrated timer max. 30 min
  • Discharge device integrated
  • Internal battery charger with deep discharge protection

S-50 DC

  • Easy Operation
  • Robust Construction, low Weight
  • Integrated timer max. 60 min
  • Discharge device external ground-discharge rod
  • Voltage measurement direct at HV output

S-80 DC

  • Easy operation
  • Robust construction, low weight
  • Integrated timer max. 60 min
  • Discharge device external ground
    rod
  • Voltage measurement direct at HV output

S-110 DC

  • Easy operation
  • Robust construction, low weight
  • Integrated timer max. 60 min
  • Discharge device external ground
    rod
  • Voltage measurement direct at HV output

S-120 DC

  • Easy operation
  • Robust construction, low weight
  • Integrated timer max. 60 min
  • Discharge device external ground
  • Voltage measurement direct at HV output

S-24 VLF

  • Extremely compact high-power VLF test device
  • Easily portable for 1-2 people
  • Simple operation: menu-assisted control with industrial class OLED display
  • Fully automatic test sequence

S-36 VLF

  • Extremely compact high-power VLF test device
  • Easily portable for 1-2 people
  • Simple operation: menu-assisted control with industrial class OLED display
  • Fully automatic test sequence

S-44 VLF (230 V)

  • Extremely compact high-power VLF test device.
  • Easily portable for 1-2 people
  • Simple operation: menu-assisted control with industrial class OLED display
  • Fully automatic test sequence

S-57 VLF

  • Extremely compact high-power VLF test device.
  • Easily portable for 1-2 people
  • Simple operation: menu-assisted control with industrial class OLED display
  • Fully automatic test sequence